DIGIHELIC LINKS communication software

$54.95 -- Configure and data log DH and DHII DP controllers

Purchase DIGIHELIC LINKS communication software

The Digihelic Links� Communications Software is an easy to use Windows� based program. Data logging and graphing can be set up by the individual control with varying logging periods. Event logging, live instrument status, remote calibration as well as uploading pre-saved configuration files are some of the higher end capabilities the Digihelic Links� Communications Software provides. The Digihelic Links� Communications Software is compatible with all Series DH and DHII Digihelic� Differential Pressure Controllers.

Programming is easy using the menu key to access 5 simplified menus which provide access to: security level; selection of pressure, velocity or flow operation; selection of engineering units; K-factor for use with flow sensors; rectangular or circular duct for inputting area in flow applications; set point control or set point and alarm operation; alarm operation as a high, low or high/low alarm; automatic or manual alarm reset; alarm delay; view peak and valley process readings; digital damping for smoothing erratic process applications; scaling the 4-20 mA process output to fit your application's range; Modbus� communications; and field calibration.

Features

� Log and graph data up to 10 units simultaneously. View up to 40 units.

� Easy to use Windows� based operator interface

� Data logging at individually adjustable rates

� On-screen graphing of process values

� Upload and download saved control configuration profiles

� Remote calibration of controls

Required Equipment

Computer Requirements: The Digihelic Links� Communications Software application will run on Windows� 95/98 and Windows� NT Workstation 4.0 (Service Pack 3 recommended), Windows� 2000 and Windows� XP software. The hardware requirements for each of these operating systems can be found in the documentation provided with that operating system. One available RS-485 port is needed to communicate with the control(s). A minimum of 4 MB of hard disk space is needed for the Digihelic Links� Communications Software application files, and additional hard disk space is needed to store data log files. Log file size will vary depending on the duration and rate selected for the controls and the number of controls on line.

Communication Requirements: To communicate with the Digihelic� Differential Pressure Controller from a PC with an RS-232 Serial Communications Port, an RS-485 to RS-232 converter is required to convert the signal from the Digihelic� Controller RS-485 format to the RS-232 input of the PC. Recommended converters are the Models 351-9 RS-485 to RS-232 converter or Model MN-21 RS-485 to USB converter. For RS-485 systems a 120-ohm resistor is also needed to terminate the last control on the control network. Shielded twisted pair cable is recommended for wiring the controls together.

Purchase DIGIHELIC LINKS communication software

SKU: DIGIHELIC LINKS

Other products in the category Accessories / Dwyer Accessories:

351-9 Dwyer RS-232 to RS-485 converter -- The Mother Node� Communication Signal Converter line of RS-232 to RS-485 converters offers an easy way to use virtually any PC to communicate with half duplex RS-485 devices. Complicated hand-shaking issues are eliminated with these easy to use . . .

A-201 Tubing for Portable Digital Manometers -- Rubber tubing, 3/16" ID, 9 ft length. Use with Dwyer hand-held digital manometers: 475, 478A, 477, and 477A.

A-266 Dwyer Digihelic Controller mounting bracket -- Surface mounting bracket. Use with Dwyer DH series digital differential pressure controllers and other Dywer differential pressure instruments

A-286 Panel Mount Flange for Magnehelic Gage -- A-286 Panel Mounting Flange for 4-1/2" Diameter Dwyer Magnehelic Gages The new mounting flange can be used on any Dwyer Instruments, Inc. gage that possesses a 4-1/2" (115 mm) diameter housing. The flange is . . .

A-298 Flat Flush Mount Bracket for Dwyer Capsuhelic -- Flat aluminum bracket for flush mounting Capsuhelic� gage

A-299 Mounting Bracket for Magnehelic Gage

A-300 Flat Mounting Bracket for Magnehelic Gage

A-301 Static Pressure Tip -- Static pressure tip for 1/4" metal tubing connectionUse with Dwyer Dwyer DH series digital differential pressure controllers and other Dywer differential pressure instruments

A-302 Static Pressure Tip -- Static pressure tip for 3/16" and 1/8"" plastic or rubber tubingUse with Dwyer DH series digital differential pressure controllers and other Dywer differential pressure instruments

A-302F-A Static Pressure Tip -- Static pressure tip with mounting flange, 4" hook style. For 3/16" ID rubber or plastic tubing, includes mounting screwsUse with Dwyer DH series digital differential pressure controllers and other Dywer differential pressure instruments

A-303 Portable Static Pressure Tip -- Portable static pressure tip for temporary insertion in ductwork. Magnet mount. For use with 3/16" ID tubing. Inserts through a small hole drilled in the side of duckwork. The magnetic mount holds the tip firmly in place. . . .

A-308 Static Pressure Fitting for Magnehelic Gage -- A-308 Static pressure fitting for Dwyer magnehelic gauges. Hose barb Fits 3/16" and 1/8" ID plastic or rubber tubing.

A-309 3-Way Manifold Valve for Dwyer Capsuhelic -- A-309 3-Way Manifold Valve for Dwyer Capsuhelic gage

A-310A 3-Way Valve for Magnehelic Gage

A-314 Bleed Fitting for Dwyer Capsuhelic -- A-314 Bleed Fitting for Dwyer Capsuhelic gage. Affords easier, safer purging of trapped air when using a Capsuhelic� gage with liquids. Also useful for draining condensate when installed in lower ports. To open, simply loosesn the hex . . .

Dwyer A-320-B Weatherproof enclosure for Dwyer differential pressure gages controllers and transmitters

A-320-B Static Pressure Tip -- Series A-320 Instrument Enclosure protects instruments in all applications. The weatherproof enclosure is water tight and corrosion resistant. Weatherproof enclosure for 3000MR Photohelic� Switch/Gage, Series 605 Magnehelic� Differential Pressure Transmitter . . .

A-321 Safety Relief Valve for Magnehelic Gage

A-370 Mounting Bracket for Dwyer Capsuhelic -- A-370 Mounting bracket. First, flush-mount the Capsuhelic� gage in the bracket, then mount the bracket to a vertical surface. Steel with gray hammertone epoxy finish.

A-402A Zippered Carry Case for Digital Manometers -- Tough gray nylon pouch protects any Series 475, 476A, 478A, 477, 477A or 490 Dwyer Digital Manometer . Double zippered for quick and easy access. With belt loop that snaps closed. Dimensions: 7-1/2�H x 3�W x 2-1/4�D (191 x 76 x 57 mm) . . .

A-432 Portable Kit for Magnehelic Gage

A-438 Dwyer mounting bracket for DHII -- Surface mounting bracket. Use with Dwyer DHII series digital differential pressure controllers.

A-464 Flush Mount Kit for Magnehelic Gage -- The A-464 Mounting Kit provides a flush mounting solution for Magnehelic� gage installations for applications such as clean rooms and mechanical equipment rooms. The A-464 can also be used as an alternative means to flush mount Magnehelic� gages on . . .

A-471Portable Kit for Dwyer Capsuhelic -- For portable operation, the A-471 Capsuhelic� Portable Gage Kit is available complete with tough polypropylene carrying case, mounting bracket, 3-way manifold valve, two 10' high pressure hoses, and all necessary fittings.

A-480 Plastic Static Pressure Tip -- Plastic static pressure tip for use with DigiMag DM-1000 series pressure and flow gauges.

A-481 Installer Kit -- Installer Kit, includes two plastic static pressure tips and 7 ft PVC tubing for use with DigiMag DM-1000 series pressure and flow gauges.

A-489 Static Pressure Tip -- Straight static pressure tip with flange, in three lengths: Model A-489, 4"Model A-491, 6"Model A-493, 8"Use with Dwyer Dwyer DH series digital differential pressure controllers and other Dywer differential pressure instruments

A-496 Heavy Duty Flush-Mount Bracket for Dwyer Capsuhelic -- A-496 Heavy Duty Flush-Mount Bracket for Dwyer Capsuhelic� gages. Use in high-shock or high vibration applications

A-605 Air Filter Kit for Magnehelic Gage

A-610 Pipe Mounting Kit for Dwyer Gages -- Conplete bracket assembly for permanently mounting Dwyer Magnehelic� and Capsuhelic� gages to pipes from 1-1/4" to 2" diameter.

A-630 SS Angle Bracket -- Stainless steel angle type bracket with stainless steel bolts for mounting Dwyer 3100 series Explosion-Proof Differential Pressure Transmitters.

A-631 SS Flat Bracket -- Stainless steel flat type bracket with stainless steel bolts for mounting Dwyer 3100 series Explosion-Proof Differential Pressure Transmitters.

A-700 Power Supply -- Dwyer A-700 Power Converter User Manual Model A-700 Power Supply is an economical and reliable power supply suitable for powering all Dwyer pressure, temperature or air velocity transmitters. Inexpensive, open-frame design allows convenient access to . . .

-B Brass Case option for Dwyer Capsuhelic water application -- Brass Case for Dwyer Capsuhelic gage. Required for water and water-based liquids.

BBV-1F Flanged 3-valve block manifold -- BBV-1F Flanged 3-valve Block Manifold for Dwyer 3100 Series Explosion-Proof Differential Pressure Transmitters. The series BBV-1 Block Manifold can be used over a broad range of industrial applications including oil refineries . . .

BBV-22F Flanged 5-valve block manifold -- BBV-22F Flanged 5-valve Block Manifold for Dwyer 3100 Series Explosion-Proof Differential Pressure Transmitters. Series BBV-2 Block and Bleed Manifold is ideal for use over a broad range . . .

DM-1200 Air Flow Option for DigMag Gage -- The airflow option enables the Dwyer DigiMag DM-1000 differential pressure gage to report air velocity and volumentric flow.Air velocity and flow readings are based upon standard dry air conditions with an ambient temperature of 70�F and a barometric . . .

HM28-0 1/8" NPT adaptor

HM28-1 Communication software and cable

HM28-2 Universal power adaptor

HM35-1 Communication Software and Cable

HM35-2 Infrared RS232 Serial Adaptor

HM35-3 External Universal Power Adapter.

HM35-PK Gas Pressure Maintenance Kit

HM35-VK Vacuum Pressure Maintenance Kit

Dwyer MiniNode RS485 to USB signal converter. No external power.

MN-1 Dwyer MiniNode RS485 to USB Converter -- MN-1 Signal Converter User Manual The Model MN-1 Mini-Node� Communication Signal Converter is a low cost device that converts half duplex RS-485 serial communications signals into a signal that can . . .

NIST Certificate for Dwyer Meters -- N.I.S.T.-traceable certificate of calibration for Dwyer instruments and gages. Lead time 1 to 2 weeks.

NISTCAL-PG1 -- Have your Dwyer Digihelic DH series and DH3 series differential pressure controllers NIST calibrated by Dwyer Instrument's accredited calibration laboratory. Less than 1 week lead time.

-SP LED Setpoint Indicator for Magnehelic Gage -- SP Indicator Product SheetSP Indicator Dimensional Drawing LED Setpoint Indicator for Dwyer Magnehelic� Gages The bright-red LED located on the scale face clearly indicates positive, negative or differential pressure when . . .